| Services Available | |
|---|---|
| Repair | Yes |
| Calibration | No |
| Free Support | Yes |
Overview
The CR200X, our smallest lowest-cost data logger, provides stand-alone operation in harsh, remote environments. It reads input from one or two sensors, then transmits the data using communication peripherals. CRBasic, its full programming language, supports simple or complex programming. Multiple CR200Xs can be configured as a network, or units can be deployed individually.
Read MoreBenefits and Features
- Ideal applications include wind energy, rural water, water level/flow, aquaculture, water quality
- Campbell Scientific’s smallest, lowest cost data logger
- Gas Discharge Tube (GDT) protected inputs
- Optimal for measuring one or two simple sensors
- Makes SDI-12, single-ended analog, pulse, switch closure, and bridge measurements
- Battery-backed clock that ensures accurate time is maintained while data logger is disconnected from battery power
- Program with LoggerNet, PC400, or Short Cut to fit your setup
- PakBus, Modbus, and SDI-12 protocols supported
Images
Related Products
Technical Description
The CR200X has several input channels for measuring a variety of sensors. Gas discharge tubes provide rugged electrostatic discharge protection for the inputs.
The CR200X does not make differential measurements and is not compatible with SDM devices, multiplexers, or thermocouples (refer to the Compatibility tab for compatible sensors, peripherals, and software). Recalibration services are not offered for the CR200X datalogger.
Videos & Tutorials
Specifications
| -NOTE- | Note: Additional specifications are listed in the CR200X-Series Specifications Sheet. |
| Maximum Scan Rate | 1 Hz |
| Analog Channels |
|
| Pulse Count Channels | 2 |
| Switched Excitation Channels | 2 voltage |
| Digital Ports |
|
| Communication Ports | 1 RS-232 |
| Switched Battery Port | 1 |
| Input Voltage Range | 0 to 2500 mV |
| Analog Voltage Accuracy | ±(0.25% of reading + (1.2 mV)x(offset)) at -40° to +50°C |
| Analog Voltage Resolution | 0.6 mV |
| A/D Bits | 12 |
| Operating Temperature | -40° to +50°C |
| Power Requirements | 7 to 16 Vdc |
| Typical Current Drain |
|
| Clock Accuracy |
|
| Protocols Supported | PakBus (leaf node only), SDI-12 |
| CE Compliance Standards to which Conformity Is Declared | IEC61326:2002 |
| Warranty | 3 years |
| Dimensions | 14.0 x 7.6 x 4.8 cm (5.5 x 3.0 x 1.9 in.) |
| Weight | 242 g (8.5 oz) |
Memory |
|
| Final Storage | 512 kB of flash memory for approximately 125,000 data points |
| Operating System | 106 kB of flash memory |
| Intermediate Storage | 8 kB of SRAM for communication buffers, calculations, variables, etc. |
Compatibility
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Sensors
| Product | Compatible | Note |
|---|---|---|
| 03002-L | ||
| 034B-L (retired) | ||
| 05103-L | ||
| 109-L | ||
| 110PV-L (retired) | ||
| CMP11-L (retired) | ||
| CS100 | ||
| CS215-L (retired) | ||
| CS300-L (retired) | ||
| CS451-L | ||
| HC2S3-L (retired) | ||
| ICEFREE3A (retired) | ||
| ICEFREE3V (retired) | ||
| TB4-L | ||
| TE525-L |
Miscellaneous
| Product | Compatible | Note |
|---|---|---|
| 014A-L | ||
| 03101-L | ||
| 05103-45-L (retired) | ||
| 05106-L (retired) | ||
| 05305-L | ||
| 083E-L (retired) | ||
| 107-L | ||
| 108-L | ||
| 109SS-L | ||
| 237-L (retired) | ||
| 255-100 | ||
| 27106T-L | ||
| 43347-L | ||
| 52202-L | ||
| A100LK-L | ||
| AM16/32B | ||
| AM25T | ||
| CMP21-L | ||
| CMP3-L | ||
| CMP6-L | ||
| CS106 | ||
| CS11-L | ||
| CS410-L (retired) | ||
| CS456-L | ||
| CS460-L (retired) | ||
| CS470 (retired) | ||
| CS471 (retired) | ||
| CS475A-L | ||
| CS475-L (retired) | ||
| CS476-L (retired) | ||
| CS477-L (retired) | ||
| CS511-L | ||
| CS526-L (retired) | ||
| CS547A-L | ||
| CS616-L | ||
| CS625-L (retired) | ||
| CS650-L | ||
| CS655-L | ||
| CS700-L | ||
| CSAT3 (retired) | ||
| CSIM11-L | ||
| CSIM11-ORP-L | ||
| ENVIROSCAN (retired) | ||
| HMP155A-L | ||
| HMP60-L | ||
| LI190SB-L (retired) | ||
| LI200X-L (retired) | ||
| LoggerNet | Version 2.1 or higher | |
| LWS | ||
| OBS-3+ (retired) | ||
| OBS300 (retired) | ||
| OBS500 (retired) | ||
| PC200 (retired) | ||
| PC400 | Version 1.0 or higher | |
| PCONNECT (retired) | Version 3.0 or higher | |
| PCONNECTCE (retired) | Version 2.0 or higher | |
| SEN12512 (retired) | ||
| Short Cut | ||
| SR50A-L (retired) | ||
| TB4MM-L | ||
| TE525MM-L | ||
| VISUALWEATHER | Version 2 or higher | |
| WINDSONIC1-L | ||
| WINDSONIC4-L | ||
| WXT520 (retired) |
Additional Compatibility Information
Communications
The CR200X can communicate with a PC via direct connect, NL201 Network Link Interface, NL240 Wi-Fi Network Link, MD485 multidrop modem, and digital cellular modems. Data can be viewed on an iOS device, an Android device, CD295 DataView II Display, or a user-supplied PDA. To use an iOS or Android device, go to the Apple Store or Google Play and download our LoggerLink Mobile Apps free of charge. User-supplied PDAs require either PConnect or PConnectCE software.
Measurement & Control Peripherals
The CR200X is not compatible with SDM devices and multiplexers.
Sensors
The CR200X can measure a variety of sensors including SDI-12 sensors and 4 to 20 mA sensors. It cannot make differential measurements and is not compatible with the freezing-rain/ice, fuel moisture/temperature, geographic position, present weather, soil heat flux, soil matric water potential, and strain sensors listed on our price lists.
Enclosures
Applications with minimal power requirements can use the ENC200 enclosure to house the data logger and the pn 16869 sealed rechargeable battery. The ENC200 cannot house a barometer or a battery that is larger than the pn 16869. However, an ENC10/12 or ENC12/14 enclosure is adequate for most CR200X-based systems.
Power Supplies
The CR200X uses an external power supply and has a built-in regulator. When connected to the on-board charging circuit, the sealed rechargeable battery should be 7 A h or smaller. Using larger batteries with the data logger's built-in charger may result in excessive PC board heating. This is especially a concern when the battery is deeply discharged or failing with a shorted cell. Campbell Scientific also recommends that solar panels be 10 W or less and wall chargers be 1 A or smaller.
Related Documents
Product Brochures
Technical Papers
Case Studies
Compliance
Miscellaneous
Downloads
CR200X Series OS v.04 (1.29 MB) 22-09-2015
Execution of this download installs the Operating System and Compiler on your computer for the following dataloggers:CR200X, CR206X, CR211X, CR216X and CR295X. It also updates the support files for the CRBasic Editor.
Note: Newer CR206X dataloggers (serial # ≥ 19122) and newer CR211X dataloggers (serial # ≥ 19143) have 250 mW radios that must use OS 3 or higher for their datalogger operating system.
Related FAQs
Number of FAQs related to CR200X: 38
Expand AllCollapse All
-
One of the simpler ways to approximate how long it will take for a data table to fill up is to open the LoggerNet Connect screen, click the Station Status button, and view the Table Fill Times tab.
-
Technically, the SRM-5A is compatible with the CR200X-series dataloggers, but it is more complicated to use it with these dataloggers. To use a SRM-5A with a CR200X-series datalogger, the SRM-5A must be in the DTE position on the station modem. In addition, user-supplied adapters and gender changers are needed to complete the connections between the SRM-5A and the RS-232 port of the datalogger. Contact Campbell Scientific for more information.
-
The CRBasic Editor Help contains example program code for all instructions in the datalogger. Look for the Example link at the top of each instruction topic. The CRBasic Help Tutorial demonstrates how to access this and other online CRBasic Editor Help files.
Also, many programming examples can be found in the datalogger and sensor manuals that are available on the Campbell Scientific website.
-
Not directly. If the CS15-L is connected to a CR200(X) datalogger, the datalogger can take the ac measurement and control a solid-state relay based on some threshold within the datalogger program. The solid-state relay can then control other relays, solenoids, or motor starters. (Use of a solid-state relay is preferred because the datalogger can trigger it with a small 5 Vdc mA signal.) For more information, see the “Measurement and Control Peripherals” section of the operator’s manual.
-
If small amounts of data are transferred per transmission, it will not be a problem. Larger amounts of data can overrun buffers in the modem, causing lost data. In that situation, lower the baud rate on the datalogger to avoid the issue.
-
Yes, but only with a direct connection, such as an RS-232 cable or a USB-to-serial adapter. While connected to the datalogger, press the Send Program button on the Clock\\Program tab, and browse to the program file.
-
It is possible to upgrade the OS without downloading each OS version between the existing one on the datalogger and the most current one available. For example, a CR1000 can be upgraded directly from OS 14 to OS 25. However, when a large jump in OS versions is made, the upgrade will likely restructure the Status table and the Setting table, and they will need to be manually reloaded.
Note that in many instances, an OS update may not be necessary. Before updating, check the OS Revision History to see if a newer version would provide desired benefits.
-
The maximum cable length depends on the interface being used.
- RS-232 connections will reach 15 m (50 ft).
- RS-485 connections go beyond 610 m (2,000 ft).
- IP connections can be routed worldwide.
-
It is not possible to connect two dataloggers to one modem and transmit data from both dataloggers. However, two dataloggers can be networked together so that data is sent from one datalogger to the other, and then the datalogger connected to the modem can transmit the data from both dataloggers.
-
The internal battery is not rechargeable. In the case of low internal battery voltage, data will only be maintained as long as a power supply is connected. Collect all data from the datalogger before disconnecting the power.
The battery, a 15598, is not user replaceable. The datalogger should be returned to Campbell Scientific to have the battery replaced. To request a returned material authorization (RMA) number, follow the steps listed on our Repair and Calibration page.
Case Studies
The semiarid region just north of the Black Hills in western South Dakota has vast......read more
Project LocationTrebonne- Ingham (S18.62843 E146.06468) System PurposeTo monitor surface water runoff from 2 different cane......read more
The National Weather Service (NWS) operates a network of automated flood-warning stations around Mount St.......read more
In the late 1970s, the National Weather Service implemented the Integrated Flood Observing and Warning......read more
In order to gain access to more reliable weather information, the Port of Tyne added......read more