Hi Folks,
I'm facing a strange problem at the time of encrypting the program for the CR1000 datalogger.
My scenario:
I have a general program for all CR1000 dataloggers which is encrypted and others additional programs that have different parameters for each application.
Unfortunately I can not post the whole program but I will present the part that is causing the problem.
1) If I try to encrypt the MMS-209_STR_.CR1(my general program) with the following portion of the code:
'**************** MeasScan - Measurements scaning ***************************** **************
Include "CPU: MeasScan.CR1"
'**************** MeasScan - Measurements scaning ***************************** **************
, through CRBASIC I have the following result:
[Version]C:\Campbellsci\Lib\Compilers\CR1Comp.exe VERSION:CR1000.Std.28.02 DATE:07/20/2015
D:\Desenvolvimento\Desenvto_software\CR1000\MMS\STR\MMS_209_STR_.CR1 -- Compiled in SequentialMode.
ProgSignature = 61223.
2) Once the MMS-209_STR_.CR1 is encrypted, when I load it in datalogger and run, I got the following error:
Running Program: "CPU:MMS_209_STR_Enc.CR1"
Run on Power Up Program: ""
Program State: compile error
===============
line 904: Undeclared variable wff.
line 904: Invalid, or out of place expression: ìÜwff, ”µô,g—Ôc_OHgOÑ“Sæ¥w....
line 906: Invalid, or out of place expression: òÑ}ÊÔ ¿>^$ yñ–>, §F¢=‡¿,ÌH1“Ì....
line 906: Undeclared variable a.
3) If I did not encrypt the MMS-209_STR.CR1, and run on the datalogger, everything works normally.
4) If I insert the content of my included file, directly into the main program, for example:
'**************** MeasScan - Measurements scaning *******************************************
'Include "CPU: MeasScan.CR1"
Scan (1,Sec,0,0)
PulseCount(AN_1,1,AN_1_PC,0,1,AN_1_Mult,AN_1_Offset)
If AN_1<=AN_1_Offset Then AN_1=0
VoltSe(UMID_2,1,mv2500,UMID_2_SeC,1,0,250,UMID_2_Mult,UMID_2_Offset)
Battery(Bat12V)
PanelTemp(PTemp_C,_60Hz)
CallTable(Table1)
CallTable(Table2)
NextScan
'**************** MeasScan - Measurements scaning *******************************************
, Everything works normally, I can encrypt and place to run in the datalogger and it works fine.
Some details:
- I have other 2 "include" instructions on the general MMS-209_STR.CR1 present no problems, the error happens only with this part of programm;
- I use the most recent version of OS, CR1000.Std.28.02
- We have more than 80 CR1000 running in our customers;
- The encryption of the general program is essential for us.
I hope was clear my explanation, and would appreciate a response as soon as possible because we are working on an important project and we need urgently a solution for our customer.
Thank you.
I don't see anything unusual about that code block, except the leading space in the file name.
Yes, But I also believe that nothing is wrong. I suspect there may be something tied to the compiler but I'm not sure.
That's possible too. If you haven't yet, I'd contact the Support Dept directly. They are responsive and helpful.
Hi Pokeeffe,
I sent the same message to the Support in Brazil.
I believe they should process this issue.
Thank you for your attention.
Best regards
* Last updated by: MSTK on 10/23/2015 @ 11:36 AM *